Walls & Trim guide
How to estimate wallpaper rolls
Count drops, not square feet. Wallpaper is hung in full-height strips (drops), and whatever is left at the end of a roll is often too short for another one. Dividing wall area by roll area can leave you a roll short.
1. Count the drops
A 12 ft (144 in) wall with 20.5 in wide paper needs 144 ÷ 20.5 = 7.02, so 8 drops. Rounding up matters: the last drop is partly trimmed but you still need a full length.
2. Find the cut length of each drop
With 8 ft walls and 4 in of total trim, each drop is 100 in. If the paper has a 21 in repeat, each drop must start at the same point in the pattern, so the cut rounds up to 5 × 21 = 105 in.
3. Drops per roll, then rolls
Rolls = round up(drops ÷ drops per roll)
A 33 ft (396 in) roll gives 396 ÷ 100 = 3.96, so 3 full drops. Eight drops ÷ 3 = 2.67, so 3 rolls, with one spare drop.
Why roll area misleads
The same roll is 20.5 in × 33 ft = 56.4 sq ft. A 96 sq ft wall divided by 56.4 suggests 1.7 rolls, so 2. The drop method says 3, because each roll ends with 96 in of paper, just short of a fourth 100 in drop, and that offcut cannot hang as a full-height strip.
Example: a whole 12 × 12 room
- Perimeter: 48 ft, or 576 in.
- Drops: 576 ÷ 20.5 = 28.1, so 29 drops.
- Cut length: 96 in wall plus 4 in trim = 100 in. With no repeat, a 396 in roll gives 3 drops.
- Rolls: 29 ÷ 3 = 9.67, so 10 rolls.
With the 21 in repeat from the earlier example, each drop rounds up to 105 in. A roll still gives 3 drops, so the answer is still 10 rolls, but with less spare paper at the end of each one. A larger repeat, such as 25 in, makes each drop 125 in and leaves only 3 drops per roll with very little to spare.
Doors, windows, and short pieces
A 36 in door takes out less than two drops, but you still hang a short piece above it, cut from the end of a roll. Below and above windows is the same. That is why counting drops around the full perimeter is the safer method, with only very wide openings such as a patio door subtracted.
Straight match versus drop match
In a straight match, the pattern lines up horizontally across every strip. In a half-drop match, every second strip starts half a repeat lower. Half- drop patterns waste more paper at the top and bottom of each drop, so add a roll if you are close to the line, or follow the manufacturer’s own calculation.
Before you order
- Read the roll width, length, and repeat from the label; they vary by brand.
- Check whether the price is per single roll while packaging is double rolls.
- Order from one batch number, and consider a spare roll for repairs.
- Half-drop and mural designs need the maker’s own planning instructions.
Frequently asked questions
How many rolls of wallpaper do I need for a 12 × 12 room?
With 8 ft walls, 20.5 in × 33 ft rolls, and 4 in of trim per drop, the 48 ft perimeter needs 29 drops at 3 drops per roll, so 10 rolls. A large pattern repeat or wide openings can change it.
Should I subtract doors and windows?
Only openings wider than a full drop, and only partly. You still need short pieces above doors and below windows, so many installers count drops around the whole room and treat the openings as allowance.
What is the difference between single and double rolls?
Some US wallpaper is priced per single roll but packaged as double rolls, which hold twice the length. Euro rolls are commonly about 20.5 in by 33 ft. Read the length on the label, not the roll count.
What does a half-drop match mean?
In a half-drop match, the pattern on each strip is offset by half a repeat from the strip beside it. It usually wastes more paper than a straight match, so follow the maker’s planning instructions.